Go Back   Indiana Truck Scene Forum > Stock and Lifted Trucks > Stock Trucks

Stock Trucks Info for your truck

Reply
 
Thread Tools Display Modes
Old 10-09-2012, 06:51 AM   #1
Devs93
Full Access Members
 
Devs93's Avatar
 
Join Date: Oct 2012
Posts: 780
Default Sloppy Steering Repair (GM)

This is an inexpensive repair That I kniw work on full fullsize up to 96
S series would also guess up 96
Should also work squarebodies
Also a Gbody car if you have one.

One of the main issues in vehicles with sloppy steering may actually be the rag joint in the steering shaft. So Before spending lots of $$$$ on new pitman ,idler arms, etc Try this first. Average cost is less than 20 bucks.

The Solution is using a steering shaft from a Jeep Cherokee XJ The steering shaft has no rag joint eliminating slop in the rag joint. Ive done this on my truck and it does make a diff!


This is a super easy swap to eliminate a butt load of steering slop. Minus my learning curve the basic swap took about 20 min.
The shafts that fit are 84-96 Jeep Cherokee XJ steering shafts. The square body, NOT the Grand Cherokee. They are almost a direct fit for OBS trucks up to 96. For 97+ there's a link at the bottom.

Start by removing the Rag joint at the bottom of the stock Shaft. Remove the bolt and pry off with a crowbar. The shaft will compress at the top.


Now remove the bolt at the top blob joint. pry or tap gently. DO NOT pound this joint. There are plastic pieces inside your steering column that will break.

Ok, now u will need to grind a SMALL groove at the top of the flat spot on the steering column joint. This is for the top bolt of the XJ shaft.

The XJ shaft will need to be separated. There is a plastic thangy inside that needs to be broken. Easiest way is to heat it with a torch and knock em apart.

Gods gift to GearHeads;

Ok,now cleanup and grease the lower end of the shaft and reinsert it into the upper.

Now grease the spline at the steering gear and slide the lower shaft on. The lower bolt will fit perfectly into the stock spline bolt groove.

Do the same for the upper, aligning the bolt with the groove u cut earlier.

Now u got a no slop steering shaft.

Enjoy!



UPDATE: For 97+ Try this. Post # 50 and 56,57
http://www.fullsizechevy.com/forum/g...eap-obs-3.html
and this.
http://www.flamingriver.com/index.php/products/c0005
__________________
http://i1262.photobucket.com/albums/...1857630329.jpg
93 ecsb 5/7 2 tone shaved smoked lights hids and leds flowmaster and some more 295/50 245/50
Deven
http://www.gmt400.com/forum/showthre...B-Build-Thread
FB
http://www.facebook.com/#!/profile.p...00001465284578
Negative Altitudes Draggin That Shit Since 2006
Devs93 is offline   Reply With Quote
Old 10-09-2012, 08:06 AM   #2
dagen_1
Full Access Members
 
dagen_1's Avatar
 
Join Date: Oct 2012
Location: Davenport, Virginia
Age: 53
Posts: 144
Default

best upgrade for the money! helped my steering tremendously.
__________________


DeWayne
'89 Cheyenne
'94 Silverado Z71
My Facebook
My Build Thread
dagen_1 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump