Indiana Truck Scene Forum - How to Recone a Sub

Indiana Truck Scene Forum (http://www.indianatruckscene.com/forum/index.php)

- Audio and Systems (http://www.indianatruckscene.com/forum/forumdisplay.php?f=28)

- - How to Recone a Sub (http://www.indianatruckscene.com/forum/showthread.php?t=223)

How to Recone a Sub

Materials that you will need.
http://i402.photobucket.com/albums/p...9/DSCN1025.jpg
http://i402.photobucket.com/albums/p...9/DSCN1026.jpg
Grind down the surround and where the spider lays down to bear metal. Then clean the entire woofer so no shavings are on it.
A card and masking tape works the best for cleaning out the pole vent.
http://i402.photobucket.com/albums/p...9/DSCN1027.jpg
Be sure to test the coils on the recone to make sure they are what you need.
http://i402.photobucket.com/albums/p...9/DSCN1028.jpg
1.5 ohms all way round babe.
http://i402.photobucket.com/albums/p...9/DSCN1029.jpg
test fit the recone.
http://i402.photobucket.com/albums/p...9/DSCN1030.jpg
http://i402.photobucket.com/albums/p...9/DSCN1031.jpg
Lay a nice bead of CA glue on where the spiders lay.
http://i402.photobucket.com/albums/p...9/DSCN1032.jpg
http://i402.photobucket.com/albums/p...9/DSCN1033.jpg
Be sure to line up the terminal leads before you spray the activator.
http://i402.photobucket.com/albums/p...9/DSCN1034.jpg
Put the shim in place and place the recone on the pole vent and get it into place.
http://i402.photobucket.com/albums/p...9/DSCN1035.jpg
Seeing as the Warden has a very small gap. I had to use a piece of paper. Usually note cards are acceptable.
And make sure the shim went all the way through the coil so its not touching anywhere. Line up the coil so you can move your make shift shim up and down easily.
http://i402.photobucket.com/albums/p...9/DSCN1036.jpg

http://i402.photobucket.com/albums/p...9/DSCN1042.jpg
http://i402.photobucket.com/albums/p...9/DSCN1043.jpg
Once finished. You can get the activator. Press down on the section of the surround you are spraying and squeeze out the CA and hold it for 20 seconds till the CA dries and the surround is laid flat.
http://i402.photobucket.com/albums/p...9/DSCN1044.jpg
http://i402.photobucket.com/albums/p...9/DSCN1045.jpg
If you are as cautious as I. You can do another layer of CA on the ring of the surround and spray with activator.
http://i402.photobucket.com/albums/p...9/DSCN1047.jpg
Time to put the dustcap on. Put a piece of tape on the center of the dustcap so you can hold it freely.
http://i402.photobucket.com/albums/p...9/DSCN1048.jpg

From there. You can begin putting CA on the ring of the dustcap.
http://i402.photobucket.com/albums/p...9/DSCN1050.jpg
Then place dustcap as desired on the subwoofer.
http://i402.photobucket.com/albums/p...9/DSCN1051.jpg
And put a ring of CA on the outside of the dustcap.
http://i402.photobucket.com/albums/p...9/DSCN1052.jpg
Then spray with Activator.
http://i402.photobucket.com/albums/p...9/DSCN1053.jpg
Then I like to place something heavy on top of the sub to put pressure on the spiders, surround, and dustcap to make sure it gets a good hold. I usually leave the heavy object on for 20 to 30 minutes.
http://i402.photobucket.com/albums/p...9/DSCN1054.jpg
After that time. Put the terminal leads into the terminals and prepare to solder.
http://i402.photobucket.com/albums/p...9/DSCN1055.jpg
http://i402.photobucket.com/albums/p...9/DSCN1056.jpg
Solder them hoes down and hope your not wasted by then.
http://i402.photobucket.com/albums/p...9/DSCN1057.jpg
http://i402.photobucket.com/albums/p...9/DSCN1058.jpg
After that. I always like to put another layer of CA on the spiders so there is NO gap and filled in nicely.
http://i402.photobucket.com/albums/p...9/DSCN1059.jpg
There you have it. A brand new sub. Now don't get too drunk.
http://i402.photobucket.com/albums/p...9/DSCN1060.jpg

reference DSBP

i never knew you could do this. Where would you geta new cone?

Ill get some info posted on it!

Sent from my VS920 4G using Tapatalk 2